Definity / Long Entry

Definity - Trunk group data block

Programmable parameters:

Class of the trunk
Lines of the trunk
Information elements of the signalling messages

Resource (trunk group) list: (BCM50 equivalent)

Parameter Description Range of possible values
No. Number of trunk (key parameter)
TAC Trunk Access Code - Code used for accessing the trunk Value range can be programmed int he dialing plan.
Type Type of the trunk

isdn -
co
did -

Name Name of the trunk string
We can indicate in the name, which points of which exchanges are connected by the trunk.
Members Number of lines in the trunk ISDN: 1...30
_TN _{Tenant Partition number - to which operation group does the trunk belong?} _1..20
COR Class of Restriction - to which class of restriction does the trunk belong? 0..95
CDR Call Detail Recording yes/no
Meas It indicates, that the exchange will send data from the trunk to the CMS (Call Management System)

internal - we send data to the BCMS (Basic CMS)
external
both
none - default

Out Disp Outgoing Display - displaying the name of trunk in the outgoing calls

no - default
yes - dialing number will be replaced with the name and number of the trunk
Que Len Queue Length - Number of held outgoing calls 0...100, 0 - nincs várakozási lista

Parameter	Description	Range of possible values
No.	Number of trunk (key parameter)
TAC	Trunk Access Code - Code used for accessing the trunk	Value range can be programmed int he dialing plan.
Type	Type of the trunk	isdn - co did -
Name	Name of the trunk	string We can indicate in the name, which points of which exchanges are connected by the trunk.
Members	Number of lines in the trunk	ISDN: 1...30
_TN	_{Tenant Partition number - to which operation group does the trunk belong?}	_1..20
COR	Class of Restriction - to which class of restriction does the trunk belong?	0..95
CDR	Call Detail Recording	yes/no
Meas	It indicates, that the exchange will send data from the trunk to the CMS (Call Management System)	internal - we send data to the BCMS (Basic CMS) external both none - default
Out Disp	Outgoing Display - displaying the name of trunk in the outgoing calls	no - default yes - dialing number will be replaced with the name and number of the trunk
Que Len	Queue Length - Number of held outgoing calls	0...100, 0 - nincs várakozási lista

Trunk group data block:

Parameter Description Range of possible values
TRUNK GROUP
Group Number:
(key parameter) Input: Number of the trunk
It is the output of the Route patterns table (Trk Grp, Grp No) 1 ...
Group Type: Type of the trunk

isdn -
co
did -

CDR Reports: Call Detail Recording yes/no
Group Name: Name of the trunk string
We indicate in the name, which ports of which exchanges are connected by the trunk
COR Class of Restriction - to which class of restriction does the trunk belong? 0..95
_TN _{Tenant Partition number - to which operation group does the trunk belong?} _1..20
TAC Trunk Access Code - A code used for accessing the trunk Value range can be programmed int he dialing plan.
Direction: Direction of the trunk two-way, incoming, outgoing
Outgoing Display? Displaying the name of trunk in the outgoing calls

no - default
yes - Dialing number will be substituted with the name and number of the trunk
Dial Access? It permits the access to the trunk with TAC y/n
_{Busy Threshold:} _{Number of busy trunk lines, after that the trunk sends an alarm signal to the operator} ₉₉
Night Service: Dialing number of the night operation mode. Every incoming call arrives to there, if the exchange is switched to a night operation mode. Dialing number
Queue Length Number of the held outgoing calls 0...100, 0 - there is no waiting list
Comm Type For the transfer of what calls will we use the trunk?

voice - default
data
alternate voice or data (avd)
alternate voice/voice grade data and 56 kbit/s (robbed bit) digital data (rbavd)

Service Type: For what kind of service is the ISDN trunk dedicated?

Auth Code? It is necessary to dial an authority code for the incoming calls yes/no
TestCall ITC: Value of the ITC (Information Transfer Capability) element can be programmed in the Bearer Capability IE of ISDN test calls. restricted, unrestricted
Far End Test Line No:
TestCall BCC: a bearer service used for ISDN test calls (BCC - Bearer Capability Class) Értékek
TRUNK PARAMETERS
Codeset to Send Display: code set of Display IE sending 0,6,7
Codeset to Send National IEs: code set of national IEs 6,7
Max Message Size to Send: Maximum size of ISDN messages sent by the exchange 260 (default),256,244,128
Charge Advice: CDR report must be switched on for this service

none - service is switched off
automatic - CA from every call
end on request - CA at the end of every call (ECS only)
during on request - CA during calling and at the end of call (ECS only)

Supplementary Service Protocol:

a (national),
b (Q-sig),
c (ETSI),
d (ECMA-name),
e (DCS - with rerouting)

Digit Handling (in/out): Protocol of the build-up of call enbloc/enbloc, enbloc/overlap, overlap/enbloc, overlap/overlap
Trunk Hunt: Algorithm of time-slot reservation descend, ascend, cyclical
Connected to Toll? an attentuation plan of the trunk

yes - trunk connects to a CO (charged) exchange
no - STT attenuation display

STT Loss: Satellite Switch Tie Trunk Loss - another attenuation plan of the trunk normal, low
DTT to DCO Loss: normal
Calling Number Callee identification - Calling Line Identification Prefix
Delete: - number of numeric characters to be deleted from the received CPN 1..15, all, blank
Insert: - numeric characters to be written to the received CPN string (1..15), blank
Numbering Format: received CPN

Numbering Format NPID Type of Number
blank unmodified unmodified
natl-pub 0001 - E.164 010 - national
intl-pub 0001 001 - international
locl-pub 0001 100 - local/subscriber
pub-unk 0001 000 - unknown
lev0-pvt 1001 - PNP 100 - local
lev1-pvt 1001 010 - Regional Level 1
lev2-pvt 1001 001 - Regional Level 2
unk-unk 0 -unknown 000 - unknown

_{Bit Rate:} _{Bit rate of modem pools applied to data transmission} _{300, 1200 (default), 2400, 4800, 9600, 19200}
_{Synchronization:} _{Method of data transmission applied on the trunk} _{async (default), sync}
_Duplex: _{Direction of data transmission applied on the trunk} _{full (default), half /duplex/}
_{Disconnect Supervision -} _{Supervicion of release} _{In? y Out? n}
_{Answer Supervision Timeout:} _{Time passed between answering the call and beginning of CDR.
Delaying of the payment} _{0...250 sec}

Parameter Description Range of possible values
TRUNK FEATURES
ACA Assignment? Automatic Circuit Assurance measurement y
Measured It indicates, that exchange will send data from the trunk to the CMS (Call Management System).
(This parameter has already occurred here earlier.)

internal - data will be sent to BCMS (Basic CMS)
external
both
none - default

Wideband Support? Is nx64k data transmission enabled? yes/no
not supported
Long Holding Time(hours): If ACA=y? 1
Internal Alert? n
Maintenance Tests? y
Short Holding Time(sec): If ACA=y? 10
Data Restriction? n
NCA-TSC Trunk Member: 1
Short Holding Threshold: If ACA=y? 15
Send Name: Display IE sending (QSIG Facility IE sending) y/n
Send Calling Number (CPN) Calling Party Number IE sending yes/no
and if the CPN table is filled out. (CH ISDN PUB)
Send Connected Number: Connected Number IE sending yes/no
Used for DCS? Is the trunk a part of a DCS? yes/no
yes - only if ssp=a,e.
There is a Definity Spec 1 message only here.
PBX ID: Exchange id. If DCS=y 1..63
DCS Signaling: d-chan
Suppress # Outpulsing? Suppressing of A # character while dialing yes/no default
Numbering Format: Attributes of the sent Calling Number and Connected Number

Numbering Format NPID Type of Number
blank unmodified unmodified
public 0001 - E.164 010 - national
private 1001 - PNP 100 - local
unknown 0 -unknown 000 - unknown

Outgoing Channel ID Encoding: exclusive
UUI IE Treatment: service-provider
Send UCID? n
Send Codeset 6/7 LAI IE? y

Parameter Description Range of possible values
INCOMING CALL HANDLING TREATMENT
Service/Feature
Called Len
Called Number
Del
Insert
Per Call CPN/BN
Night Serv.

Parameter	Description	Range of possible values
	INCOMING CALL HANDLING TREATMENT
Service/Feature
Called Len
Called Number
Del
Insert
Per Call CPN/BN
Night Serv.

Parameter Description Range of possible values
TRUNK GROUP
Administered Members (min/max): Number of lines of trunk group. 1...30
Total Administered Members:
GROUP MEMBER ASSIGNMENTS Trunk lines
Port Output: Identifiers of trunk (DS1 interface) card and trunk lines (PCM time-slots) 01A1001..., 01A1101...

01A - cabinet identifier
10,11 - Output: DS1 interface card identifier
01... - PCM number of time-slot

Code
Sfx
Name
Night
Sig Grp - Signalling group Output: Identifier of the signalling link transmitting signalling messages of trunk lines.

Parameter	Description	Range of possible values
	TRUNK GROUP
Administered Members (min/max):	Number of lines of trunk group.	1...30
Total Administered Members:
	GROUP MEMBER ASSIGNMENTS	Trunk lines
Port	Output: Identifiers of trunk (DS1 interface) card and trunk lines (PCM time-slots)	01A1001..., 01A1101... 01A - cabinet identifier 10,11 - Output: DS1 interface card identifier 01... - PCM number of time-slot
Code
Sfx
Name
Night
Sig Grp - Signalling group	Output: Identifier of the signalling link transmitting signalling messages of trunk lines.